Click on a link below to learn more about Particulate Samplers, Dust
samplers, Cyclones, and IOMs from SKC
 |
The SKC Aluminum Cyclone is a lightweight respirable dust sampler
that is used with a filter loaded into a three-piece filter cassette.
The SKC cyclone gives sharp size selection between respirable
fractions at 4 or 5 µm. |
|
 |
The SKC Button Aerosol Sampler is a reusable filter sampler with
a porous curved-surface sampling inlet designed to improve the
collection characteristics of inhalable dust. The SKC Button
Sampler meets the ACGIH/ISO sampling criteria for inhalable particulate
mass. See also the SKC
Abrasive Blasting Sampler for Heavy Metals |
|
 |
sampling equipment that meets the requirements of NIOSH 5040
or MSHA specifications for sampling Diesel Particulate Matter
(DPM). |
|
 |
The Most Portable 10 L/min Ambient PM10 Sampling
System Available. SKC has brought portability, cost effectiveness,
and ease of use to ambient PM10 sampling with the SKC Deployable
Particulate Sampler (DPS) System.
SKC has combined its fully programmable Leland Legacy® Sample Pump
with the DPS-10 Impactor and sampling accessories to create this convenient
turnkey system.
|
|
 |
The SKC IMPACT single-stage inertial impactor is designed
for the efficient collection of PM10 or PM2.5 in ambient air.
A sampling pump operating at 10 L/min draws PM through the
impactor; larger particles are captured on a disposable pre-oiled
impaction substrate while smaller particles collect on a 47-mm
filter. |
|
 |
The GS-3 Cyclone is a 10 mm, lightweight, 2-piece conductive
plastic unit that holds a standard 37 mm filter cassette for
collecting respirable dust particles. The GS-3 cyclone is designed
to meet the ACGIH/CEN/ISO Curve. |
|
 |
The GS-1 Cyclone, a single-inlet version of the GS-3 Cyclone,
provides performance equivalent to the Dorr-Oliver Cyclone,
but has the added advantage of being constructed of conductive
plastic |
|
 |
The IOM sampler is a reusable filter cassette with a sampling
head designed to better measure the worker's exposure to total
airborne particulates. |
|
 |
Only the SKC Parallel Particle Impactor (PPI) has
the power of 4 impactors in 1 small sampler to provide the
closest match to the ACGIH/ISO/CEN thoracic or respirable curves.
A job no single personal impactor can do alone! |
|
 |
The Personal Environmental Monitor (PEM) is a lightweight, personal
sampling device for collecting particulates of either 2.5 or
10 µm aerodynamic equivalent diameter. |
|
 |
SKC Personal Modular Impactors (PMIs)
are designed for the highly efficient collection of PM10, PM2.5,
or PM Coarse(PM10-2.5). |
|
 |
The personal-size Sioutas Cascade Impactor separates
and collects airborne particles in five size ranges. he Sioutas
Impactor is highly efficient at collecting particles without
the use of impaction grease or substrate coatings and at
retaining labile compounds for size-fractionated chemical
analysis.
|
|
| |
|
|
Particulate Monitors
|
|
 |
The 3886 Handheld Laser Particle Counter simultaneously
monitors five particle size channels to provide concentration
measurement of 0.3, 0.5, 1.0, 3.0, and 5.0-micron particles.
Add optional probes for relative humidity/temperature and
air velocity for simultaneous monitoring of these important
indoor air parameters.
|
|
 |
The EPAM-5000 particulate air monitor is available in three different
kit configurations: a 10 µm kit, 2.5 µm kit, and a
1.0 µm kit. Each kit contains the EPAM-5000 monitor with
a specific cut-point sampling head, battery charger, HazComm
PC software and computer cable, shoulder strap, and manual. |
|
 |
The HAZ-DUST is a real-time dust monitor designed for industrial
hygiene studies, HazMat investigations, and remediation projects. |
|
 |
The HAZ-DUST IV personal real-time aerosol monitor, with
new infrared detector, provides you with immediate breathing
zone measurements of aerosol and dust for industrial hygiene
and environmental air investigations. The small, lightweight
unit attaches onto a worker's belt while the miniature sensor
easily clips to a worker's collar. Select from inhalable,
thoracic, or respirable sampling heads to target a specific
fraction. An in-line 37-mm cassette behind the sensor allows
the user to collect a concurrent filter sample for gravimetric
or chemical analysis.
|
|
 |
Digitally record workplace dust exposure with the HAZ-DUST
VDM-7500 wireless video dust monitoring system. The VDM-7500
measures levels of lung-damaging particles while simultaneously
overlaying dust concentration onto video images.
|
|
 |
The Micro-Environmental Monitor (MEM) is a line-operated compact
aerosol sampling system for collecting particulates of either
2.5 or 10 µm aerodynamic equivalent diameter. |
|
 |
The economical and easy-to-use SPLIT2 Dust Monitor is designed
for personal or area monitoring for respirable, thoracic, or
inhalable dust. SPLIT2 is a passive dust monitor that can become
an active monitor by combining it with a 2 L/min sample pump
and GS Cyclone or IOM sampling head for dust monitoring and concurrent
dust sampling |
